top of page
Matching stair nosing for hybrid flooring

INSTALLATION · STAIRS

Hybrid and laminate flooring on stairs

Stairs are where a floor is seen most and worn hardest. Hybrid and laminate both work on stairs, but they're installed differently from the rest of the house: glued, not floating, with a stair nosing on every step. Here's how it's done, what you need, and when to hand it to us.

How the edges are finished

Stair nosing covers the front of each step, and an L-moulding finishes the floor where it meets the stairs.

 

 

Stair nosing on hybrid flooring stairs

Stair nosing

Covers the front edge of each step and takes the wear.

L-moulding finishing a floor edge at a step

L-moulding

A neat, square finish where the floor meets a step.

01

Can you put hybrid flooring on stairs?

Yes. The treads and risers are covered with the same boards as the floor, cut to size and glued down. The front edge of each tread gets a stair nosing: a matching profile that wraps the edge, protects it from kicks and gives your foot a safe edge to land on. Laminate is done the same way. Engineered oak can be done too, usually with a solid timber nosing.

02

Why stairs are glued, not floated

A floating floor needs room to move. A stair tread is a small, isolated piece with people landing on its edge all day, so it's fixed: construction adhesive to the tread, the nosing glued and usually screwed from underneath or through the face and plugged. The expansion gap rule still applies at the walls, hidden under a small scotia or a bead of colour-matched silicone.

03

What you need per step

  • One tread board, cut to depth and width; often one board does it, wide boards look best.

  • One riser piece, cut from a board or a matching riser strip.

  • One stair nosing in the matching colour, cut to width. Nosings come in set lengths, so count steps and allow for cuts.

  • Construction adhesive, a mitre or drop saw, and clamps or weights while the glue sets.

Order the boards for the stairs with the floor so the colour batch matches. The calculator handles the floor; add roughly one box for every six steps.

04

Open or closed stairs

Closed stairs (tread plus riser against a wall) are straightforward. Open-sided stairs need the exposed end finished with a matching trim or a mitred nosing, and a landing is treated as a small floor with nosings on its edges. Winders (the triangular steps on a turn) take time to template; this is where most DIYers call us.

05

Safety and finish

The nosing is a safety part, not decoration: it's what stops the edge chipping and what your heel catches. Fit it square, glued and fixed, with no lip above the tread. Keep the same colour the whole way up. If the stairs are in a rental or a busy family home, choose a hybrid with a 0.5mm wear layer, such as Elegant 6.5mm, or a 9.5mm board like Duro.

06

When to let us do it

In Coffs Harbour, Grafton, Brisbane, the Gold Coast and surrounding areas our own team installs stairs with the rest of the floor. Winders, open sides, long flights and matching an existing floor are all quoted after a free measure. Book a free measure.

07

Stair flooring questions

Can hybrid flooring go on stairs?

 

Yes, glued down with a matching stair nosing on each step. It's one of the most common things we install.

 

Do I need stair nosing with hybrid flooring?

 

Yes. It protects the edge of the board and gives a safe step. Without it the front edge chips and the floor voids its warranty on the stairs.

 

How do you install stair nosing?

 

Cut it to width, dry-fit it over the finished tread, glue with construction adhesive and fix according to the nosing's profile (screwed from below or face-fixed and plugged). Clamp until set.

 

Can I put laminate on stairs?

 

Yes, the same way. Choose an AC4 or AC5 laminate for the wear.

 

How much flooring do stairs need?

 

Roughly one box per six steps for the treads and risers, plus one nosing length per step. Order it with the floor so the batch matches.

bottom of page